美國NDT JAMES P-C-7300 Bond Test MK III粘結強度測試儀可由直接拉脫的方法量度混凝土、瀝青、磁磚、混凝土收復或其他表面物料的粘力或拉力。

The James Bond Tester™ MK III or pull off adhesion test measures the bond strength or tensile strength of concrete, asphalt, tile, concrete repair, or other overlay material by the direct tension or pull off method. By pulling a 25mm steel disk attached to the material under the unit can,

1. Measure the near surface strength of a substrate in order to determine the substrates quality before applying an overlay
2. Determine the bond strength of a repair or overlay material after it is applied to the substrate
3. Determine the tensile strength of a repair, overlay or adhesive after the material is applied to the surface

The James Bond Tester™ MK III  has been successfully used to verify the quality of existing materials, determine the adhesion strength of shotcrete, tile, epoxies, paint and other repair materials or coatings.

Purchasing Notes
 

• Each System comes with 10, 50mm 2 inch, ASTM Standard 1583 - 04  stainless steel disks
• Customers who purchase this may also need the T-M-170 Moisture Master or T-HT-1000 Humitest for substrate moisture testing

Features and Benefits

·         Accurate bond strength of repair mortars, epoxy resins, laminates, overlays, and other coatings.

·         Calibrated gauge with maximum load indicator and mechanical damping.

·         Ball Joint Design for rapid testing as well as assuring direct tensile loading

·         Adjustable alignment plate with built in leveling facility for both vertical and horizontal pulls.

·         Compact design.

·         Easy to use.

·         Standards

o    ISO 4624 Paints and varnishes -- Pull-off test for adhesion

o    EN 1015-12 Methods of test for mortar for masonry. Determination of adhesive strength of hardened rendering and plastering mortars on substrate

o    EN 1348 Determination of Tensile Adhesion Strength for Cementitious Adhesives

o    BS 1881 Part 207 Testing concrete. Recommendations for the assessment of concrete strength by near-to-surface tests

o    ASTM C 1583 Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)

o    ASTM D 4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers

o    ACI 503-30 Guide for the Application of Epoxy and Latex Adhesives for Bonding Freshly Mixed and Hardened Concretes

o    DIN 1048 Part 2 Testing concrete; testing of hardened concrete (specimens taken in situ)

• Specifications:
•  

以上是美國NDT JAMES P-C-7300 Bond Test MK III粘結強度測試儀的詳細信息，如果您對美國NDT JAMES P-C-7300 Bond Test MK III粘結強度測試儀價格、廠家、品牌、型號、圖片、規(guī)范、規(guī)格、原理有疑問，或需要詳細報價單、宣傳冊、中英文產品說明書，請點擊我公司

美國NDT James相關產品介紹：

美國NDT James T-HT-1000 Humiditest混凝土鉆孔濕度測試儀

美國NDT James T-C-10 T-C-20 Cementometer微波水泥含水率測試儀

美國NDT James T-S-30 Aquaprobe微波土壤含水率測試儀

美國NDT James T-M-170 Aquameter混凝土含水率測試儀

美國NDT James T-T-90 Trident插針式微波骨料含水率測試儀

美國NDT James I-CB-6000 Carbo Detect混凝土碳化深度酸堿指示劑

美國NDT James I-AS-3000 ASR-Detect混凝土堿骨料反應測試儀

美國NDT James A-AB-1200 A-AV-1300 A-AA-1100 Air Meters混凝土含氣量測試儀

美國NDT JAMES Z-WP-1000 Windsor Probe混凝土強度槍擊檢測儀

美國NDT JAMES W-P-2000 Windsor Pin混凝土強度檢測儀

美國NDT JAMES R-HR-8000 Mini R-Meter鋼筋定位儀

美國NDT JAMES P-C-7300 Bond Test MK III粘結強度測試儀

美國NDT JAMES P-C-728 P-C-729 Anchor錨栓測試儀

美國NDT JAMES M-M-3056 Maturity Meter混凝土成熟度測試儀

美國NDT JAMES Datascan MK II鋼筋混凝****達

美國NDT James C-P-6000 C-P-6050 Porosiscope混凝土滲氣滲水性測試儀

美國NDT James C-CM-4000 Cor-Map鋼筋銹蝕檢測儀

美國NDT James C-CL-3000 Chlorimeter混凝土氯離子含量測定儀

美國NDT James W-M-350 W-M-250 Rebound Hamme機械回彈儀

美國NDT James W-D-2000 Rebound Hamme數字回彈儀

美國NDT James V-E-1000 E-Meter MK II動態(tài)彈性模量測試儀

美國NDT James V-V-100 Vu-Con沖擊回波測試儀

美國NDT JAMES V-C-400 V-Meter MK IV混凝土超聲波測試儀

美國NDT James C-CS-8000 C-CS-8300 Gecor 8鋼筋銹蝕程度測定儀

美國NDT James C-RM-8000 Ohmcorr混凝土電阻率測定儀

美國NDT James C-CM-5000 Cor-Map II大屏幕半電池電壓鋼筋銹蝕檢測儀

美國NDT JAMES R-C-400/450/475/410 Rebarscope鋼筋掃描儀